StreetStangs.net  

Go Back   StreetStangs.net > Technical > Dyno Room

Reply
 
Thread Tools Display Modes
Old 07-09-2011, 04:27 PM   #1
01silver freak
Senior Member
 
01silver freak's Avatar
 
Join Date: Nov 2007
Location: Eastaboga/Coldwater
Posts: 296
Send a message via AIM to 01silver freak
03 GT first time dyno

Took my car for its and my first dyno ever since ive always been curious to see what my actual numbers were. I'll try to get the graphs on here Soon but the car made 308.7HP @3700RPM and 490.6TQ @2900RPM on its first pull. The torque is WAY OFF but ill go with it
Run 2 was 304.7/485.5
Run 3 was 300.7/461.3

Humidity was at 50% and it was also 98.8 degrees!
__________________
2001 GT: BBK underdrive pulleys,Mgw Short-throw,JLT RaI, Lots of apperance mods~ Dead

2003 GT: Motive 3.90's,BBK 78mm TB/Plenum, Steeda Underdrive pulleys,Vrs O/R X-pipe,JLT RaI,SLP LoudmouthII catback, SCT Tuned 13.4 @ 108 ~ Sold
01silver freak is offline   Reply With Quote
Old 07-09-2011, 06:02 PM   #2
QWKSNKE
3v's are slow
 
QWKSNKE's Avatar
 
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
Not trashing your numbers but your hp is off too. HP readings are a direct calculation of the torque readings. So if the torque numbers are off with the dyno, than the whole thing is a wash because it can't calculate HP either. Did C.A.M dyno it?

Aside from that, unless you were spraying nitrous on the pulls, there is no way a 2v car can put down that much HP with the mods in your sig.

Again, I am not being a jackass. Just trying to help you out. Whoever dyno'd it, needs to refund your money or give you some more pulls when they get the machine fixed
__________________
2009 Porsche Carrera S
2008 ///AMG C63.. Eurocharge Tune. RIP
2019 AMG GLC43..wife's
03 F250 SD.. Edge Evo, AFE Stage 1 CAI
08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's
01 Cobra vert... wife's

I need a new toy
QWKSNKE is offline   Reply With Quote
Old 07-09-2011, 07:48 PM   #3
TheJeanyus
Administrator
 
Join Date: Dec 2004
Location: Huntsville, AL
Posts: 14,774
Yep, the load calculations are way off on that dyno.
__________________
1998 Mustang GT Coupe - World's Slowest Racecar
2005 Toyota 4Runner SR5 V8
2013 Volkswagen Jetta Sportwagen TDI
TheJeanyus is offline   Reply With Quote
Old 07-09-2011, 08:08 PM   #4
01silver freak
Senior Member
 
01silver freak's Avatar
 
Join Date: Nov 2007
Location: Eastaboga/Coldwater
Posts: 296
Send a message via AIM to 01silver freak
Sadly the car will probably sold before i can take it to reputatle shop i figured i would of seen 270ish.
__________________
2001 GT: BBK underdrive pulleys,Mgw Short-throw,JLT RaI, Lots of apperance mods~ Dead

2003 GT: Motive 3.90's,BBK 78mm TB/Plenum, Steeda Underdrive pulleys,Vrs O/R X-pipe,JLT RaI,SLP LoudmouthII catback, SCT Tuned 13.4 @ 108 ~ Sold
01silver freak is offline   Reply With Quote
Old 07-09-2011, 08:41 PM   #5
rtusnake
Halfshaft Killer
 
rtusnake's Avatar
 
Join Date: Mar 2005
Location: The Kingdom
Posts: 3,910
How much is 3 pulls there?
__________________
03 Cobra
06 F250
(\__/)
(='.'=)
(")_(")
rtusnake is offline   Reply With Quote
Old 07-09-2011, 08:58 PM   #6
01silver freak
Senior Member
 
01silver freak's Avatar
 
Join Date: Nov 2007
Location: Eastaboga/Coldwater
Posts: 296
Send a message via AIM to 01silver freak
It was 50$ but normally i have no clue how much it cost.
__________________
2001 GT: BBK underdrive pulleys,Mgw Short-throw,JLT RaI, Lots of apperance mods~ Dead

2003 GT: Motive 3.90's,BBK 78mm TB/Plenum, Steeda Underdrive pulleys,Vrs O/R X-pipe,JLT RaI,SLP LoudmouthII catback, SCT Tuned 13.4 @ 108 ~ Sold
01silver freak is offline   Reply With Quote
Old 07-09-2011, 09:16 PM   #7
EHardy1971
Trunk Monkey
 
EHardy1971's Avatar
 
Join Date: Jun 2007
Location: Home
Posts: 5,708
Quote:
Originally Posted by QWKSNKE View Post
Not trashing your numbers but your hp is off too. HP readings are a direct calculation of the torque readings. So if the torque numbers are off with the dyno, than the whole thing is a wash because it can't calculate HP either. Did C.A.M dyno it?

Aside from that, unless you were spraying nitrous on the pulls, there is no way a 2v car can put down that much HP with the mods in your sig.

Again, I am not being a jackass. Just trying to help you out. Whoever dyno'd it, needs to refund your money or give you some more pulls when they get the machine fixed
Especially on the bolded part. Those torque numbers are in modded Lightning/Terminator territory.
__________________
Eric
89 LX Coupe-Juiced
01 Lightning-Boost
06 TBSS
EHardy1971 is offline   Reply With Quote
Old 07-09-2011, 10:32 PM   #8
banditmwp
Welcome to America!
 
banditmwp's Avatar
 
Join Date: Dec 2004
Location: in the 11's
Posts: 4,501
Send a message via AIM to banditmwp Send a message via Yahoo to banditmwp
Did they do the dyno pull in 4th gear?

Just thinking maybe a 3rd gear pull skewed the numbers way out of line.
__________________

91 GT Convertible

2006 Nissan Titan LE Crew Cab
2014 Peterbilt 337/Marion 22' box
banditmwp is offline   Reply With Quote
Old 07-10-2011, 03:40 PM   #9
yellowSVT
Senior Member
 
yellowSVT's Avatar
 
Join Date: Mar 2007
Location: anniston/saks
Posts: 1,459
where did u take it?
__________________
http://i171.photobucket.com/albums/u...DSC02715-1.jpg
2004 cobra MGW shifter,spec 3+ clutch, billet flywheel, 3.75 upper pulley, banssanni exaust, 3.4 whipple, 60lb injectors, fore rails and hat, gt40 pumps, dual bypass heat exchanger. 660hp/600tq
http://s171.photobucket.com/albums/u...t=M2U00182.flv
2012 f150 4x4 5.0 blk
2012 rzr LE S orange
2012 rzr LE silver/blk
2003 DSG lightning
2001 ford focus ZX3 silver
yellowSVT is offline   Reply With Quote
Old 07-10-2011, 04:08 PM   #10
rtusnake
Halfshaft Killer
 
rtusnake's Avatar
 
Join Date: Mar 2005
Location: The Kingdom
Posts: 3,910
You know what kind of dyno they use?
__________________
03 Cobra
06 F250
(\__/)
(='.'=)
(")_(")
rtusnake is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 03:11 AM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.