Kenne Bell Supercharger 2010 Camaro SS - Page 10

EZ SPEED · 03-16-2012, 10:11 AM

here is before and after

.

Blown54 · 03-16-2012, 12:26 PM

I bet that matte vinyl was tuff to lay in those curves and under the grille line...
End result= looks killer.

TheJeanyus · 03-16-2012, 12:40 PM

Quote:

Originally Posted by EZ SPEED

I agree about the stripe under the headlights!
The red pinstripe on the wheels is just a red vinyl stripe that I got off ebay. they make them pre-curved to fit certain diameter wheels. mine is 5mm wide for a 20" wheel. it comes to you in 4 pieces per wheel. pretty easy to install.

That's the same kind of stuff I have on my bike. Once in a while I'll notice part of mine trying to peel up, but it sticks back down. If it gets too bad I may have to buy another set...for a whopping $6. IIRC mine is 3mm for a 17" wheel.

EZ SPEED · 03-17-2012, 04:59 AM

Quote:

Originally Posted by Blown54

I bet that matte vinyl was tuff to lay in those curves and under the grille line...
End result= looks killer.

LOL..You know it was ...since your the one who installed it after I gave up...LMAO

EZ SPEED · 06-18-2012, 03:22 PM

I re-dynoed the car today with 12 #'s of boost.

Final numbers BOGUS..so I removed them.

We tried some 15 # pulls, but the belt kept jumping off ...Booooo !!!

since Last dyno (605 / 561) I added 3#'s of boost along with an 8 Rib Pulley setup and added a "Super Chiller" ...the chiller runs my intercooler fluid through a box that is tapped into my air conditioner to help lower the Inlet Air Temperature. We were able to lower the IAT by about 50 degrees more than usual and add more timing. Also I think my transmission was slipping a little bit last dyno becauue I didnt follow the correct fill proceedure and was almost 3 quarts low (didnt figure that one out till I got home after last dyno and was doing some test and tune on a deserted road)

coupe · 06-18-2012, 03:35 PM

If I didn't know any better, I'd have thought that torque curve was from your truck.

EZ SPEED · 06-18-2012, 03:37 PM

Quote:

Originally Posted by coupe

If I didn't know any better, I'd have thought that torque curve was from your truck.

Yeah ..except the truck torque is double that number now.....LOL. should be around 1080- 1100 next time I dyno it

Skillet · 06-18-2012, 06:05 PM

That's a ton of power! I want a ride!

natedawgg94 · 06-18-2012, 06:24 PM

damn nice #s to bad the belt wouldnt let ya hit 16 ....

rtusnake · 06-18-2012, 09:50 PM

So when is it going to the track?

06-18-2012, 03:22 PM	#95
EZ SPEED Friends Join Date: Dec 2004 Location: Tempe Arizona Posts: 3,029	I re-dynoed the car today with 12 #'s of boost. Final numbers BOGUS..so I removed them. We tried some 15 # pulls, but the belt kept jumping off ...Booooo !!! since Last dyno (605 / 561) I added 3#'s of boost along with an 8 Rib Pulley setup and added a "Super Chiller" ...the chiller runs my intercooler fluid through a box that is tapped into my air conditioner to help lower the Inlet Air Temperature. We were able to lower the IAT by about 50 degrees more than usual and add more timing. Also I think my transmission was slipping a little bit last dyno becauue I didnt follow the correct fill proceedure and was almost 3 quarts low (didnt figure that one out till I got home after last dyno and was doing some test and tune on a deserted road) __________________ 2020 Range Rover Sport HSE P525 Dynamic - Firenze Red - Supercharged 5.0 - 518 HP SOLD - 2010 Camaro SS [/B] - Featured in GM High Tech Performance and Camaro Now Magazines - http://www.superchevy.com/features/g...of-perfection/ Last edited by EZ SPEED; 07-03-2013 at 07:15 AM.

06-18-2012, 06:24 PM	#99
natedawgg94 Senior Member Join Date: Apr 2005 Location: Ohatchee, AL Posts: 713	damn nice #s to bad the belt wouldnt let ya hit 16 .... __________________ 1994 Cobra Pace Car #365 of 1000 light mods 1994 mustang GT 3.55's, 331 stroker, 75mm tb, 75mm maf, mac h pipe SOLD (ole yella u will be missed ((>>. Rubbing Is Racing

06-18-2012, 09:50 PM	#100
rtusnake Halfshaft Killer Join Date: Mar 2005 Location: The Kingdom Posts: 3,910	So when is it going to the track? __________________ 03 Cobra 06 F250 (\__/) (='.'=) (")_(")

03-16-2012, 12:26 PM	#92
Blown54 Senior Member Join Date: Mar 2005 Posts: 145	I bet that matte vinyl was tuff to lay in those curves and under the grille line... End result= looks killer.

06-18-2012, 03:35 PM	#96
coupe Super Moderator Join Date: Dec 2004 Posts: 6,313	If I didn't know any better, I'd have thought that torque curve was from your truck.

06-18-2012, 06:05 PM	#98
Skillet Lazy Bum Join Date: Aug 2005 Location: Moody Posts: 1,649	That's a ton of power! I want a ride!