01-01-2009, 09:34 PM | #1 |
5.slo stanger
Join Date: Jan 2007
Location: oxford alabama
Posts: 735
|
add me
everyone can now add me to the i hate heater cores club just got mine done and after 4 hrs i drov it out of the neiborhood and it started overheating soooo i changed the thermostat well tried to change it the bolts were right behing the waterpump and you cant get them soo i went running around town trying to find ballheaded allen wrenches and to no avail finanally found them later that night and then found out that thw therm housing/water neck was threaded so its impossible to get the bolt to thread in evenly so the water neck wouldnt seal and then i had to get another one finally got it put to gether and bam then the waterpump started leaking so i bought the gaskets and took everything off when my dad says oops i forgot to tighten this hose so we tightned the hose and everything ran like a sewing machin just figgured i would share my heartaches w/ yall
thanks taylor
__________________
no mustangs anymore but i do have a 1jz swapped 83 supra |
01-01-2009, 10:17 PM | #2 |
Gone but not forgotten
Join Date: May 2008
Location: 4/08/2013. Went to the man upstairs. RIP
Posts: 955
|
Taylor - I feel your pain! I just got done replacing the timing chain cover on my 86, along with all the heater hoses & thermostat. On the thermostat housing I have the allen head bolts - I think I used a ball headed 8mm allen wrench with a bit trimmed off the short end. Tedious, but it went well. Now this weekend I gotta do a heater core in my wife's (MagsNag) 90 LX. Not looking forward to it!
__________________
-Don 86GT (sleeping in the garage for now) 87 T-bird Turbo Coupe (daily driver) 87 Ranger ($100 work truck) Meat is murder!... Tasty, tasty murder. |
01-01-2009, 11:17 PM | #3 |
5.slo stanger
Join Date: Jan 2007
Location: oxford alabama
Posts: 735
|
its not stupid bad its just tedious and awkward and i broke the mess out of the mounting tabs that hold on the gauge cluster surround the part that has the light switch and hazard light switch so now it kinda moves when i turn on the lights and other lil stuff like that but i will tell you take out all the bolts in the firewall before you take out the dash there is one big screw type bolt that is a self drilling screw but big and the head is inside the car the other 2 are under the hood if you do like me and only take out the 2 under the dash youll pull the heaterbox out and only come like half way out and then you have to put the whole thing back together to get the one screw out and then take it all back apart to take thos out before you take the dash off or your headed for trouble
__________________
no mustangs anymore but i do have a 1jz swapped 83 supra |
01-02-2009, 12:16 AM | #4 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Only heater core replacement i will do is on a factory non-a/c equipped car. The non a/c cars take all of about 20 minutes to change the heater core.
I have no problems whatsoever paying someone a couple hundred bucks to replace a heater core in a a/c equipped car
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
01-02-2009, 10:08 AM | #5 |
Dayuuuuuuum!!!!!
Join Date: Dec 2004
Location: Dallas GA
Posts: 2,933
|
I do heater cores on ANY Fox Mustang for $100 plus parts.Same day service too
__________________
86 Mustang Gt......Mods piling up in my garage.
07 F350 dooly.....Tows my fifth wheel |
01-02-2009, 11:29 AM | #6 |
Gone but not forgotten
Join Date: May 2008
Location: 4/08/2013. Went to the man upstairs. RIP
Posts: 955
|
Wow - That's reasonable!!! I don't mind doing heater cores, but on the 90 I'm gonna have my hands full with diagnosing. The vents & floor work, but the defrost doesn't. So, I'm thinking a vacuum motor, but I'll know more when I get into it.
__________________
-Don 86GT (sleeping in the garage for now) 87 T-bird Turbo Coupe (daily driver) 87 Ranger ($100 work truck) Meat is murder!... Tasty, tasty murder. |
01-04-2009, 06:37 PM | #7 |
Gone but not forgotten
Join Date: May 2008
Location: 4/08/2013. Went to the man upstairs. RIP
Posts: 955
|
Heater core is done on the 90. Not too bad - the vacuum motor that actuates the defrost was dead - so I got another and we're all good. Now I don't have to use my hand to wipe the window in the mornings!
__________________
-Don 86GT (sleeping in the garage for now) 87 T-bird Turbo Coupe (daily driver) 87 Ranger ($100 work truck) Meat is murder!... Tasty, tasty murder. |
01-04-2009, 10:09 PM | #8 |
5.slo stanger
Join Date: Jan 2007
Location: oxford alabama
Posts: 735
|
way to go did you see that bolt i was talkin about
__________________
no mustangs anymore but i do have a 1jz swapped 83 supra |
01-04-2009, 10:55 PM | #9 |
Gone but not forgotten
Join Date: May 2008
Location: 4/08/2013. Went to the man upstairs. RIP
Posts: 955
|
Yeah - I think. I used a 7/16's socket with a long extention to get it out. It's right at the bottom of the box - right at the carpet line. It's almost like a self tapping sheet metal screw that goes right through the firewall down at the bottom. Anyway, yeah - it was a bit of a project because I had to check all the vacuum motors...then had to find a replacement for one. While I had the dash out, I had other issues to fix as well. There's a steel plate that holds the fuse block. That was broke - fixed it. I think the most frustrating thing was just trying to find and fix all the problems the previous owner left for me. Either way, it's done! I got no leftover screws and 98% of the previous rattles are all gone! (and no - I didn't use a buch of bubble gum and shoe strings!) Much better!!! Now if I could just find another 200 horsepower for it!!
__________________
-Don 86GT (sleeping in the garage for now) 87 T-bird Turbo Coupe (daily driver) 87 Ranger ($100 work truck) Meat is murder!... Tasty, tasty murder. |
|
|