06-26-2005, 08:22 AM | #11 |
Senior Member
Join Date: May 2005
Location: ALBERTVILLE, AL
Posts: 498
|
Re: Spring Decisions
can you cut a rear spring though? arent they made where ya cant? and it fit in the saddle again. The front is differant the top of the spring is same diameter as rest of the spring. but the rear spring is smaller at the top and the bottom correct?
|
06-26-2005, 08:32 AM | #12 | |
Nothing new here
Join Date: Dec 2004
Location: Senoia, GA
Posts: 2,990
|
Re: Spring Decisions
Quote:
Also the top of both the front and rear do not have a specific position detail. Actually onlt the front bottom does.
__________________
1974 Triumph TR6 1985 Monte Carlo SS 1986 Mustang GT 2011 KIA Optima GTS |
|
06-26-2005, 08:38 AM | #13 |
Senior Member
Join Date: May 2005
Location: ALBERTVILLE, AL
Posts: 498
|
Re: Spring Decisions
ok so the rear spring has the same diameter as the rest of the spring also (except for the pigtail which sets on the lower control arm? Thanks its been a while since i changed springs and wasnt 100% sure on the rear spring.
so how much to cut to achieve a 1.5 inch drop. half a coil or 1 complete coil? btw I have 4 banger springs in the rear, and stock v8s up front, they are rated differant so probly wouldnt cut as much out of a 4 banger spring as you would a v8 spring right? I did this on a silverado once. and 1 coil took nearly 3 inches out, but this is a larger truck and heavier. |
06-27-2005, 12:27 AM | #14 |
Member
Join Date: Mar 2005
Location: Sacramento California
Posts: 449
|
Re: Spring Decisions
I would have to agree, I would not cut the stock springs. I did it on mine and it rode like shit. It was way to soft and rolled bad. I then purchased and installed Motorsport C springs. It rides a tad stiffer than stock but handles much better.
__________________
EEC Analyzer A9M, TwEECer, 306ci, 73mm C&L w Tuner Tube, Cobra Intake, 42# inj, Edelbrock 6037, E303 cam, 155 fuel pump, FPR, 70mm TB, E-Fan, 3.55 gears, Powerdyne 9psi actual 5psi...way more. |
06-27-2005, 03:53 PM | #15 |
Beach Bum
Join Date: Dec 2004
Location: In the sun!
Posts: 2,846
|
Re: Spring Decisions
I wouldnt cut the stockers. I would get Tommy's CC's and some Steeda sport springs.
|
06-27-2005, 04:04 PM | #16 |
Friends
|
Re: Spring Decisions
Blah...
I cut a full coil on the fronts on my 89 and had no problems. Lowered the front about 1-1.5 inches and gave it a nice rake...the back end was lower before this. I would say, as easy as it is to do it and remove/install, I'd try it. If you don't like it, save the money for some diffferent springs. Its easy for people to say buy this, buy that. But you won't know 'til you try it.
__________________
2001 Cobra 'Vert Procharged and Intercooled 455rwhp/441rwtq Work Car: 2005 Honda Odyssey 400 whp Turbo V6, 6-speed, full cage, H&R Suspension, Brembo Brakes |
06-27-2005, 04:26 PM | #17 | |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Re: Spring Decisions
Quote:
Don't know what was different in your 89, but each fox I have put springs on is a freaking nightmare. The lower a-arms do not release enough to slide the springs in like they do on the 94 ups. Takes 2 people with prybars to get the fronts in. Besides, all you gain with cutting coils is a 'look'. You don't get anywhere near the performance that any aftermarket spring has to offer.
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
|
06-27-2005, 04:35 PM | #18 | |
Friends
|
Re: Spring Decisions
Quote:
You're right, it will never handle as good as aftermarket springs. But its a cheap cosmetic mod in my book.
__________________
2001 Cobra 'Vert Procharged and Intercooled 455rwhp/441rwtq Work Car: 2005 Honda Odyssey 400 whp Turbo V6, 6-speed, full cage, H&R Suspension, Brembo Brakes |
|
06-27-2005, 04:56 PM | #19 |
Nothing new here
Join Date: Dec 2004
Location: Senoia, GA
Posts: 2,990
|
Re: Spring Decisions
Well, I only don't want to cut the OEM springs, just in case the car is ever worth anything, I am trying to save all the original parts.
I had thought about doing a cut job on some springs, but just more for a time issue decieded to go ahead and buy some instead. I have been saving for several months so now I have the money for them, I might as well do it. I did look into cutting a bit, I have all the needed tools already, but the biggest factor would be the increase rates, and on the vert, I want a little softer ride, something that is just a touch hard than stock and thats about all. So I have deceided to buy the M5300G springs, I can get them from www.johnbleakleyford.com for $198, the springs are made by Eibach, they have a 1.5" F/R drop, but I will most likely eliminate the front isolator to pick up another 1/4" drop or so. I have also bought Tommy's C/C plates, and am looking at the Steeda .4" offset aluminum rack bushings.
__________________
1974 Triumph TR6 1985 Monte Carlo SS 1986 Mustang GT 2011 KIA Optima GTS |
06-28-2005, 03:39 PM | #20 | |
Beach Bum
Join Date: Dec 2004
Location: In the sun!
Posts: 2,846
|
Re: Spring Decisions
Quote:
|
|
|
|