04-20-2009, 10:56 AM | #11 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Have you checked the oil level? If the oil level gets to low you will have this problem
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
04-20-2009, 11:23 AM | #12 |
Trunk Monkey
Join Date: Jun 2007
Location: Home
Posts: 5,708
|
If your running a Fram oil filter,that could also be the problem. They have been known to collapse internally and cause catastophic oil pressure loss.
__________________
Eric 89 LX Coupe-Juiced 01 Lightning-Boost 06 TBSS |
04-20-2009, 12:46 PM | #13 | |
Daddy x4 ...we're done
Join Date: Dec 2004
Location: Oxford, AL
Posts: 11,551
|
Quote:
They are press-in plugs (very much like the "freeze plugs" in the block) and probably not likely to come out on a stock motor. However, if someone rebuilt that motor, they may not have put them in good enough and one could've come out. On a sid note, there's also another oil passage plug pointing straight down at the rear of the lifter valley under the lower intake.
__________________
-Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring |
|
04-20-2009, 01:56 PM | #14 |
5.slo stanger
Join Date: Jan 2007
Location: oxford alabama
Posts: 735
|
ok i pulled the distributor and there is no oil pump driveshaft to be found so this is my problem the only thing i am wondering is what caused this problem ohh and opil level is perfect
__________________
no mustangs anymore but i do have a 1jz swapped 83 supra |
04-20-2009, 03:16 PM | #15 |
Daddy x4 ...we're done
Join Date: Dec 2004
Location: Oxford, AL
Posts: 11,551
|
Your oil pump went bad, siezed up, and twisted the shaft in half.
__________________
-Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring |
04-20-2009, 04:07 PM | #16 |
Trunk Monkey
Join Date: Jun 2007
Location: Home
Posts: 5,708
|
Yep. Looks like engine pulling time!
__________________
Eric 89 LX Coupe-Juiced 01 Lightning-Boost 06 TBSS |
04-20-2009, 04:15 PM | #17 |
Daddy x4 ...we're done
Join Date: Dec 2004
Location: Oxford, AL
Posts: 11,551
|
Look at the good side... it's a great time to fix any leaking gaskets you may have.
Lee and I just did this on the '86 two weekends ago and it no longer leaves oil spots everywhere it goes.
__________________
-Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring |
04-20-2009, 09:39 PM | #18 |
5.slo stanger
Join Date: Jan 2007
Location: oxford alabama
Posts: 735
|
yea but i am in college and working alot! so i guess she will just sit till i can afford a cherry picker and engine stand and then i might be able to fix it but im not pullin out the motor without rebuilding it compleatly and doin some performance goodies im thinkin like stroker,heads,forged goodies the whole shebang so.. looks like the stang will be down for a whil on the upside i did just buy a 97 jeep today with only 96k on the clock so things are lookin up
__________________
no mustangs anymore but i do have a 1jz swapped 83 supra |
04-20-2009, 10:28 PM | #19 |
Trunk Monkey
Join Date: Jun 2007
Location: Home
Posts: 5,708
|
I have an engine stand you can borrow. I have an engine hoist too,if you can get everything done so it's ready to hook up and pull out,give me a yell.
__________________
Eric 89 LX Coupe-Juiced 01 Lightning-Boost 06 TBSS |
04-21-2009, 01:03 PM | #20 |
5.slo stanger
Join Date: Jan 2007
Location: oxford alabama
Posts: 735
|
thanks soo much eeric i will give ya a call pm me your number
__________________
no mustangs anymore but i do have a 1jz swapped 83 supra |
|
|