07-13-2006, 06:02 PM | #71 |
5.0 Block/Walnut Cracker
Join Date: May 2005
Location: Working....
Posts: 2,409
|
Re: Mass Air on 2.3's
Svobrown,
Can you send me another datalog like the one that you sent before? Need to see what the MAF voltage is when it goes rich. I have found the proper MAF adjustment (I hope)... After I get the datalog I will make a small change and send the chips back for you to try...that way we can see what effect it will have on the AFR. |
07-13-2006, 09:32 PM | #72 |
Senior Member
Join Date: Nov 2005
Location: Graham AL
Posts: 1,461
|
Re: Mass Air on 2.3's
I will do it first thing Friday. I'm at work tonight.
__________________
''Life's tough... it's even tougher if you're stupid.'' - - John Wayne |
07-15-2006, 05:16 AM | #73 |
Senior Member
Join Date: Nov 2005
Location: Graham AL
Posts: 1,461
|
Re: Mass Air on 2.3's
I started looking closer at the datalog I sent. I may understand what your talking about on the maf stuff now.
How does the tps work on the timing and injectors (fuel) I know i will get full boost at low tps, can this be made so I can control the thottle more instead of just getting full power at low thottle? ??Less timing in the lower thottle and more as the rpms and tps go up. Cutting my teeth on this question so. Go easy on the poor boy.
__________________
''Life's tough... it's even tougher if you're stupid.'' - - John Wayne |
07-15-2006, 09:45 AM | #74 | |
5.0 Block/Walnut Cracker
Join Date: May 2005
Location: Working....
Posts: 2,409
|
Re: Mass Air on 2.3's
Quote:
On the items below I have used the current TwEECer software names for those that use the TwEECer & LA3. MAP - M_0B06 desired load not knocking (rescaled) MAP - M_0D47 Base Ignition (Regular) Table is 5 or 6 degrees above a stock LA3 binary. MAP - M_OC8C Premium Ignition (Premium) Table is about 3 deg. higher up to around 4500 rpm. Function - F_052C - Wot enrichment vs RPM Function - F_1010 - Air Mass Transfer Function - F_1038 - VAF Transfer Function - F-1038 - MAF Transfer BAP =29, VAT=100_F_1010=0.227, P_0402=0.227 Function - F-1038 - MAF Transfer F_1010=0.250, P_0402=0.25 These are just a few of the items that I am trying to get tied together at the moment... |
|
07-15-2006, 09:56 AM | #75 | |
Senior Member
Join Date: Nov 2005
Location: Graham AL
Posts: 1,461
|
Re: Mass Air on 2.3's
Quote:
|
|
07-15-2006, 10:03 AM | #76 | |
5.0 Block/Walnut Cracker
Join Date: May 2005
Location: Working....
Posts: 2,409
|
Re: Mass Air on 2.3's
Quote:
You probably did see what I was talking about but I want to try to make sure I kind of understand how all of these tie together in tuning... |
|
07-20-2006, 05:48 PM | #77 |
Senior Member
Join Date: Nov 2005
Location: Graham AL
Posts: 1,461
|
Re: Mass Air on 2.3's
How is the learning curve going?
__________________
''Life's tough... it's even tougher if you're stupid.'' - - John Wayne |
07-20-2006, 06:55 PM | #78 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Re: Mass Air on 2.3's
He is probably looking for some liquor now
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
07-21-2006, 11:11 PM | #79 | ||
5.0 Block/Walnut Cracker
Join Date: May 2005
Location: Working....
Posts: 2,409
|
Re: Mass Air on 2.3's
Quote:
find it this weekend I will go ahead and ship your chips back. Then when I get it finished I will mail you a chip to try. I do not want to send you anything until I can try it on mine first. Quote:
On a side note - just to let you guys know I like my AEM setup with the small amount of time (break from 2.3L stuff) that I have played with it. It "REALLY" does give you complete tuning control..... |
||
07-22-2006, 01:53 AM | #80 | |
Senior Member
Join Date: Nov 2005
Location: Graham AL
Posts: 1,461
|
Re: Mass Air on 2.3's
Quote:
|
|
|
|