07-16-2007, 01:39 PM | #21 |
Daddy x4 ...we're done
Join Date: Dec 2004
Location: Oxford, AL
Posts: 11,551
|
How do you figure?
Even if he had to buy a different bell housing, crossmember, and driveshaft yoke it shouldn't be more than $2K. However, being that he's not set-up for a T-5 currently, he'll have to buy all that stuff no matter which route he takes.
__________________
-Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring |
07-16-2007, 02:28 PM | #22 |
*WWIP* Saving for Evo XXI
Join Date: Dec 2004
Location: You like my biodata. B-i-o-d-a-t-a!
Posts: 1,693
|
I've seen prices for the 500 for about 1875, and the 600 for 1975.
Looks like the the price I posted was wrong. The remanu with the dog gears is 2k$, and a new T-5 with street gears is $2k. I think I'll stick with street (syncro) set. However, they're not showing hp ratings nor prices on upgrades. I think I'll call here and try to price one out. edit: GForce just quoted me $2500 for a new trans with proper upgrades. Quite a bit higher.
__________________
08 cbr 1000 73 mach 1 Last edited by 99LS1; 07-16-2007 at 02:56 PM. |
07-16-2007, 03:29 PM | #23 |
Super Moderator
Join Date: Dec 2004
Posts: 6,313
|
Call Walt @ ProMotion Powertrain. Tell him Matt from SPEC clutch sent you. He may mark the price up a little. But he carries T5 stuff and Tremec stuff. He is very knowledgable and will not lead you down a road you don't need just for a sale.
__________________
" If you can't explain it simply, you don't understand it well enough. " - Albert Einstein |
07-16-2007, 06:15 PM | #24 | |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Quote:
Don't you have a 351c in your car? Does anyone make the necessary stuff to install the tko in your car? (bellhousing, crossmember, driveshaft)
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
|
07-16-2007, 06:33 PM | #25 |
Senior Member
Join Date: Jan 2006
Location: Looking for more ways to add BOOST
Posts: 167
|
We have a 600 in a 88 Mustang, had to go into the trans with less than 1000 miles on it. The guy at tremec would never admit there was anything wrong, BUT he sent us some upgraded shift fingers for Free?, Along with a complete tear down and rebuild Manuel. The fingers helped, now it will shift with just boost, but you cant spray it and shift without letting off the spray. The t5 that was in the car would shift fine, till my buddy hulled 3RD gear shift fork. We will not buy another 600 tko. We have put the T5 gear set in from astro performance, so far the trans has worked fine.
__________________
Hauling A** on Pump Gas !!!!! |
07-16-2007, 07:56 PM | #26 |
Daddy x4 ...we're done
Join Date: Dec 2004
Location: Oxford, AL
Posts: 11,551
|
That's what I'll likely be trying next.
__________________
-Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring |
07-16-2007, 08:23 PM | #27 |
*WWIP* Saving for Evo XXI
Join Date: Dec 2004
Location: You like my biodata. B-i-o-d-a-t-a!
Posts: 1,693
|
Several people make the bellhousing that bolts up. I want to say it's the same bolt patteron as a 289/302/351 since the 351c is from the small block family.
I don't believe the driveshaft yoke is a problem either. The crossmember can be modified. I've looked at several parts list and it's really not that involved. Tremec 3550 ($800.00) Tremec Shifter (Free with tranny) Tremec bellhousing ($50.00) Flywheel (came with bellhousing had it balanced to match my flexplate) Flywheel Bolts ($20.00) Driveshaft Yoke (I used the one from my C4) Clutch Pedal (Came with Clutch Pedal Assymboly $100) Clutch fork ($20.00) Throwout Bearing (Included with Clutch Fork) Clutch and Pressure Plate ($195 for the first one, $175 for the second) Pressure Plate Bolts ($10.00) Crossmember (Modified my C4 Crossmember) Two 3/8 8” grade 8 bolt (15.00) with locking nuts and washers Two 3” pieces of 1” diameter pipe Tranny Fluid ($6.00) Shifter Boot ($3.00 from junkyard)
__________________
08 cbr 1000 73 mach 1 |
07-16-2007, 08:29 PM | #28 | |
Daddy x4 ...we're done
Join Date: Dec 2004
Location: Oxford, AL
Posts: 11,551
|
Quote:
__________________
-Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring |
|
07-16-2007, 08:31 PM | #29 |
*WWIP* Saving for Evo XXI
Join Date: Dec 2004
Location: You like my biodata. B-i-o-d-a-t-a!
Posts: 1,693
|
Doh. Wouldn't it be easier to tell me what to buy so I can pull the trigger on something I think I'm overanalyzing the situation.
__________________
08 cbr 1000 73 mach 1 |
07-16-2007, 08:37 PM | #30 |
Dayuuuuuuum!!!!!
Join Date: Dec 2004
Location: Dallas GA
Posts: 2,933
|
are you going to swap to a cable style clutch or use the factory z bar setup?
__________________
86 Mustang Gt......Mods piling up in my garage.
07 F350 dooly.....Tows my fifth wheel |
|
|